LTC4216
9
4216fa
For more information www.linear.com/LTC4216
applicaTions inForMaTion
Hot Circuit Insertion
When circuit boards are inserted into a live backplane, the
supply bypass capacitors can draw huge transient current
from the power bus as they charge. Potentially, the flow
of current could damage the connector pins and glitch
the power bus, causing other boards in the system to
reset. The LTC4216 is designed to turn on or off a circuit
board supply in a controlled manner, allowing insertion
or removal without glitches or connector damage.
Overview of LTC4216 Features
1. Allows safe board insertion and removal from a live
backplane.
2. Controls load voltages from 0V to 6V.
3. High side gate drive for external N-channel MOSFET.
4. Adjustable soft-start with inrush current limiting for
large load capacitor during start-up.
5. Adjustable analog current limit (ACL) with circuit
breaker fault time-out during an overcurrent fault condi-
tion. No external gate capacitor is required for the ACL
loop compensation.
6. Electronic circuit breaker tripping at 25mV across the
sense resistor. The response time is adjustable through
an external capacitor at the FILTER pin.
7. Provides an ON pin to turn on and off the device. This can
also be used to reset the device after a circuit breaker trip.
8. Provides output supply voltage monitoring through the
FB pin and signals the RESET pin output.
9. Provides fault status output.
ON Control
The ON pin has two hysteretic comparators with differ-
ent threshold levels (0.8V and 0.4V) and they serve two
purposes:
1. Turn on the device if the ON pin voltage > 0.8V for more
than 6祍 and turn it off if the ON pin voltage < 0.72V for
more than 15祍.
2. Reset the device if the ON pin voltage < 0.4V for more
than 30祍 after a circuit breaker trip.
There are various methods of setting the ON pin
voltage:
1. Tie the ON pin to the load supply (V
IN
) through a 10k
pull-up resistor.
2. Drive the ON pin with an ON/OFF logic signal from the
system controller.
3. Connect an external resistive divider at the ON pin.
This divider can be used to set a higher value for the load
supply undervoltage lockout voltage than the internal V
CC
undervoltage lockout circuit.
For example, as shown in Figure 17, if both V
CC
and
SENSEP pins are connected to a 5V load supply, choosing
the resistive divider values, R1 = 20k, R2 = 80.6k, turns on
the device when the load supply voltage reaches around
80% of its final value.
V
CC
Undervoltage Lockout
A hysteretic comparator, UVLO, monitors bias supply (V
CC
)
for undervoltage. The thresholds are defined by V
CC(UVL)
(2.12V) and its hysteresis, 擵
CC(UVL,HYST)
(120mV). When
V
CC
rises above V
CC(UVL)
, the device is enabled. When
V
CC
falls below (V
CC(UVL)
擵
CC(UVL,HYST)
), the device is
disabled and GATE is pulled low. If V
CC
cycles below this
threshold for more than 200祍, following a circuit breaker
trip, it clears the fault latch. Any bias supply glitches that
last less than 10祍 will be rejected by the UVLO glitch filter.
Timer
An external capacitor, C1, is used at TIMER pin to provide
two timing cycles for the LTC4216. The first timing cycle
is the debounce cycle when the ON pin is first turned on,
both the GATE and SS pins are held low and any short-
circuit faults are ignored by the electronic circuit breaker.
Second timing cycle is the power-good delay before the
RESET pin goes high when the FB pin voltage exceeds
0.6V and its hysteresis.
The TIMER pin sources 2礎 into C1 during the two timing
cycles and is then pulled low by an internal N-channel
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LTC4221IGN#TRPBF
IC CTRLR HOTSWAP DUAL 16SSOP
LTC4222CG#PBF
IC CTRLR DUAL HOT SWAP 36-SSOP
LTC4223CDHD-2#PBF
IC CNTRLR HOT SWAP DUAL 16-DFN
LTC4224IDDB-2#TRPBF
IC CNTRLR HOT SWAP DUAL 10-DFN
LTC4225IGN-1#PBF
IC CONTROLLER HOT SWAP 24-SSOP
LTC4230CGN#TRPBF
IC CONTRLLR HOT SWAP TRPL 20SSOP
LTC4232CDHC#TRPBF
IC CTLR HOT SWAP 5A 16-DFN
LTC4240IGN#TRPBF
IC CTRLR HOTSWAP CPCI I2C 28SSOP
相关代理商/技术参数
LTC4216IMS
制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow Voltage Hot Swap Controller
LTC4216IMS#PBF
功能描述:IC CNTRLR HOT SWAP 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件
LTC4216IMS#TRPBF
功能描述:IC CNTRLR HOT SWAP 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件
LTC4217
制造商:LINER 制造商全称:Linear Technology 功能描述:2A Integrated Hot Swap Controller
LTC4217CDHC
制造商:LINER 制造商全称:Linear Technology 功能描述:2A Integrated Hot Swap Controller
LTC4217CDHC#PBF
功能描述:IC CTRLR HOT SWAP 2A 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF)
LTC4217CDHC#TRPBF
功能描述:IC CTRLR HOT SWAP 2A 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件
LTC4217CDHC-12
制造商:LINER 制造商全称:Linear Technology 功能描述:2A Integrated Hot Swap Controller